ATX BAR 50mm OLYMPIC 220 CM MAX 700KG POWER BAR BLACK/CHROME

In stock
SKU
LH-50-ATX-LDBC
Rating:
0% of 100
ATX ® offers top-quality, tested and proven equipment for professional use
  • the maximum limit load of the bar is 700 kg for a wide grip, e.g. Bench press
  • reduced limit load of the bar 400kg for a narrow grip, e.g. dead lift
  • minimum limit load of the bar 300kg at a point, e.g. squat (see image below)

The ATX Power Bar ® is a precise - made of tough elastic spring steel barbell in the high-end finishes.
Whether for Crossfit, Weight Lifting - keep ® barbells or power lifting, the ATX was also in extreme demand
and therefore meet the highest standards.
Faces encapsulated high quality with ATX ® color code logo
Color code / color: black
Material: tough elastic spring steel
Carrying capacity: 700 KG (Detailed information on exposure limits and application of technology)
Net weight: 20.0 KG + / - 0.2%
Overall length: 2200 mm
Handlebar measurements: 1310 mm
Handle bar diameter: Ø28, 5 mm
Recordings Ø: Ø 50 mm, with fine anti-slip finish
Recording / storage: silky smooth pivot bearing with precision brass bushings
Edge: fine, very grippy with 2-fold Reach marking
Mark / grip widths: 810/910 mm
Surface Coating: Combined coating - handle bar with high quality black hybrid coating. Disc recordings with extremely abrasion-resistant Qualitätsverchromung
Type of load transfer maximum allowable load weight of the dumbbell exercises as
Wide grip width: 700 KG Bench Press
Mean grip width: 400 KG Deadlift
Selectively middle / narrow handle width: 300 KG Squat
The following table shows the permitted uses for the dumbbell are listed.
Approval application notes & limitations
Fitness: YES
Crossfit: YES must be used if appropriate solid rubber weight plates and shedding mats!
Weightlifting: YES must be used if appropriate solid rubber weight plates and shedding mats!
€319.00
ali
Hitro in enostavno obročno odplačevanje Že od 10.43 € Vaš mesečni obrok
+ 0 € polog
Izračun obrokov

Potrebujete dodatne informacije o izdelku? Pokličite nas na 051 453 105 ali pa nam pošljite povpraševanje.

Send inquiry
Product is currently Out of stock.
Enter your email and get an update when product is back in stock.
ATX ® offers top-quality, tested and proven equipment for professional use
  • the maximum limit load of the bar is 700 kg for a wide grip, e.g. Bench press
  • reduced bar limit load of 500kg for a narrow grip, e.g. dead lift
  • minimum limit load of the bar 400kg at a point, e.g. squat (see image below)

ATX® offers superior, tested and proven equipment for professional use.

ATX® power bar is made of alloyed special steel / spring steel precision-made barbells in a high-end finish
The rods have a very high tensile and compressive strength with simultaneous elasticity.
Thus, the rods can be deformed to a certain stress (elastic limit), then without permanent deformation
return elastically to its original state.
The decisive factor here is the optimal quality of the alloy, among others chromium, molybdenum, silicon, manganese.

The ATX® barbells are therefore unique in this segment price / performance!

In ATX® barbells through a German independent laboratory for testing the following material tests:

Tensile test acc. DIN EN ISO 6892-1
Tensile test acc. DIN EN ISO 6892-1

Rockwell hardness acc. DIN EN ISO 6508-1
Rockwell hardness acc. DIN EN ISO 6508-1

The barbell has the following values:

Tensile strength (Tesile Strength): 206000 psi = 206 K (K / ksi = kilo pounds per square centimeter)
= / Corresponds to 1420 N / mm2
HRC / surface hardness: 44.0
Whether for functional fitness, weights - or powerlifting, ATX® Barbell bars keep even the most extreme demands and was therefore meet the highest standards. The front sides are surrounded by quality, color-coded ATX® logo

Color Code / Color: black

The ATX Power Bar ® is a precise - made of tough elastic spring steel barbell in the high-end finishes.
Whether for Crossfit, Weight Lifting - keep ® barbells or power lifting, the ATX was also in extreme demand
and therefore meet the highest standards.
Faces encapsulated high quality with ATX ® color code logo
Color code / color: black
Material: tough elastic spring steel
Carrying capacity: 700 KG (Detailed information on exposure limits and application of technology)
Net weight: 20.0 KG + / - 0.2%
Overall length: 2200 mm
Handlebar measurements: 1310 mm
Handle bar diameter: Ø28, 5 mm
Recordings Ø: Ø 50 mm, with fine anti-slip finish
Recording / storage: silky smooth pivot bearing with precision brass bushings
Edge: fine, very grippy with 2-fold Reach marking
Mark / grip widths: 810/910 mm
Surface Coating: Combined coating - handle bar with high quality black hybrid coating. Disc recordings with extremely abrasion-resistant Qualitätsverchromung
Type of load transfer maximum allowable load weight of the dumbbell exercises as
Wide grip width: 700 KG Bench Press
Mean grip width: 400 KG Deadlift
Selectively middle / narrow handle width: 300 KG Squat
The following table shows the permitted uses for the dumbbell are listed.
Approval application notes & limitations
Fitness: YES
Crossfit: YES (must be used if appropriate solid rubber weight plates and shedding mats!)
Weightlifting: YES (must be used if appropriate solid rubber weight plates and shedding mats!)
Write Your Own Review
You're reviewing:ATX BAR 50mm OLYMPIC 220 CM MAX 700KG POWER BAR BLACK/CHROME
Your Rating